BS EN 10244-1-2009 Steel Wire and Wire Products - Part 1 General Principles
|
ID： |
00B0C2797E984993A7FF956C944F6826 |
|
文件大小(MB)： |
0.28 |
|
页数： |
12 |
|
文件格式： |
|
|
日期： |
2009-7-9 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BS EN,10244-1:2009,ICS 25.220.40; 77.140.65,NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW,BRITISH STANDARD,Steel wire and wire,products — Nonferrous,metallic,coatings on steel wire,Part 1: General principles,This British Standard,was published under the,authority of the Standards,Policy and Strategy,Committee on 31 May,2009.,. BSI 2009,ISBN 978 0 580 62602 9,Amendments/corrigenda issued since publication,Date Comments,BS EN 10244-1:2009,National foreword,This British Standard is the UK implementation of EN 10244-1:2009. It,supersedes BS EN 10244-1:2001 which is withdrawn.,The UK participation in its preparation was entrusted to Technical,Committee ISE/26, Steel wire.,A list of organizations represented on this committee can be obtained on,request to its secretary.,This publication does not purport to include all the necessary provisions,of a contract. Users are responsible for its correct application.,Compliance with a British Standard cannot confer immunity,from legal obligations.,BS EN 10244-1:2009,EUROPEAN STANDARD,NORME EUROPéENNE,EUROP腎SCHE NORM,EN 10244-1,April 2009,ICS 25.220.40; 77.140.65 Supersedes EN 10244-1:2001,English Version,Steel wire and wire products - Non-ferrous metallic coatings on,steel wire - Part 1: General principles,Fils et produits tréfilés en acier - Revêtements métalliques,non ferreux sur fils d'acier - Partie 1 : Principes généraux,Stahldraht und Drahterzeugnisse - überzüge aus,Nichteisenmetall auf Stahldraht - Teil 1: Allgemeine Regeln,This European Standard was approved by CEN on 13 December 2008.,CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European,Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national,standards may be obtained on application to the CEN Management Centre or to any CEN member.,This European Standard exists in three official versions (English, French, German). A version in any other language made by translation,under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the,official versions.,CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.,EUROPEAN COMMITTEE FOR STANDARDIZATION,COMITé EUROPéEN DE NORMALISATION,EUROP腎SCHES KOMITEE FüR NORMUNG,Management Centre: Avenue Marnix 17, B-1000 Brussels,. 2009 CEN All rights of exploitation in any form and by any means reserved,worldwide for CEN national Members.,Ref. No. EN 10244-1:2009: E,BS EN 10244-1:2009,EN 10244-1:2009 (E),2,Contents Page,Foreword .3,1 Scope ..4,2 Normative references .4,3 Terms and definitions 4,4 Requirements relating to coating 4,4.1 Requirements for the specific type of metal and alloy .4,4.2 Coating mass .4,4.3 Appearance of coating ..5,4.4 Special finishes .5,4.5 Adherence of coating .5,5 Test conditions .5,5.1 Selection of samples ..5,5.2 Determination of mass of coating ..6,5.2.1 Gravimetric method .6,5.2.2 Other methods ..7,5.3 Adherence test ..7,5.4 Retests 8,BS EN 10244-1:2009,EN 10244-1:2009 (E),3,Foreword,This document (EN 10244-1:2009) has been prepared by Technical Committee ECISS/TC 30 “Steel wires”,the secretariat of which is held by AFNOR.,This European Standard shall be given the status of a national standard, either by publication of an identical,text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at,the latest by October 2009.,Attention is drawn to the possibility that some of the elements of this document may be the subject of patent,rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.,This document supersedes EN 10244-1:2001.,This European Standard for non-ferrous metallic coating on steel wire is made up of the following parts:,. Part 1: General principles,. Part 2: Zinc or zinc alloy coatings,. Part 3: Aluminium coatings,. Part 4: Tin coatings,. Part 5: Nickel coatings,. Part 6: Copper, bronze or brass coatings,According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following,countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech,Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,……
……